A pool table is a complicated and expensive piece of furniture, and it can be difficult to take it apart and put it back together again. This guide will show you how to take a pool table apart and put it back together again, so that you can keep it in good condition for years to come.
What You Will Need
To disassemble a pool table, you will need the following:
-A Phillips screwdriver
-A level
-An 8” level
-Pool table screws
-Pool table nails
-Pool table felt
-Pool table sandpaper (220 grit)
How to Disassemble a Pool Table
Pool tables come in a variety of shapes and sizes, so it can be tough to know where to start when trying to disassemble one. This guide will walk you through the entire process, from removing the legs to taking apart the table top.
1. Remove any hinges or screws that hold the legs together. You can either use a screwdriver or a hammer to pop them off, or use a pry bar if you have access to one.
2. Pry off the top of the table using a pry bar or a screwdriver. You may need to remove some of the wood around the edges if it’s stuck on tightly.
3. Remove any screws that are holding the table top on. If there are any nails holding it down, remove them first with a nail puller.
4. Carefully pull off the top of the table, being sure not to rip any of the wires or cables that run underneath. Once it’s free, set it aside and move on to step 6.
5. Remove any screws that are holding down the legs of the table. Again, if there are nails holding them down, remove them first with a nail puller before pullingoff the legs.
6. If the table has a skirt (the wooden cover on the bottom of the table), remove it by carefully prying it off with a screwdriver or a hammer. Be sure to remove any screws that are holding it down, as well as any nails that are holding it in place.
7. Sand the edges of the table where the top and bottom meet if they’re rough or unfinished. You can also use 220 grit sandpaper to rough up the surface if you want.
8. Reattach the legs to the table top using new screws and nails, being sure to line them up correctly. Make sure that the screws and nails are tight, or your table may not stand up well to use!
9. Replace the skirt if you removed it in step 6, and reattach any wires or cables that were loose when you took it apart. Finally, replace any screws or nails that were missing when you took it apart, and you’re finished.
Step-by-Step Guide
If you have ever wanted to take your pool table down and put it back together again, this is the guide for you! In this post, we will walk you through the entire process of disassembling a table so that you can easily put it back together.
Before getting started, make sure to gather the following items:
- Pool Table
- Allen Wrench
- Plyers Hammer
- Jigsaw
- Tape Measure
- Circular Saw
- Dust Mask and Goggles
- Safety Glasses
1. Start by removing the legs from the pool table. You will need to remove 2 screws on each leg and then pull them off. Make sure to keep the screws in a safe place as you will need them later.
2. Next, remove the railings from around the edge of the table. These are held on by 4 screws that are located near each end of the railing. Once these screws are removed, simply pull the railing away from the table. Be careful not to damage the wood with your jigsaw.
3. Next, remove all of the padding from around the edge of the table using yourhammer and a screwdriver. You will also need to remove the shelves that are located at each end of the pool table. Be sure to save all of the padding, screws, and shelves.
4. Next, use your jigsaw to cut around the edges of the table so that it is completely free from wood. Make sure to take care not to cut into any wires or plumbing.
5. Once the table is free from wood, you can start putting it back together by reassembling the legs first. Make sure that you match up the screws that you removed in step 1 and replace them in the same locations on each leg. Next, reattach the railings using the screws that you saved in step 3. Finally, attach the shelves using the screws that you saved in step 4. Make sure to line up the holes that are located near each end of each shelf before attaching them.
6. Once everything is attached, put a piece of tape measure along one edge of the table and then use your jigsaw to cut a hole in the middle of that measurement. Be sure to leave a few inches on either side of the hole so that you can fit your railings back into place.
Tips for Safe Pool Table Disassembly
Pool tables are typically made of strong wood and metal, and can be quite difficult to disassemble without the correct tools. Here are some tips for safe and easy pool table disassembly:
- 1. Always wear safety goggles when working with tools and parts of the pool table.
- 2. Have a sturdy workbench or bench mounted tool stand available in case any part of the pool table falls off.
- 3. Secure all pieces of the pool table before starting to disassemble it. This will help prevent any accidental movements that could cause further damage.
- 4. Use a Phillips screwdriver to unscrew the screws that hold the legs of the pool table together. Be sure to label each screw so you can put them back in the same location when you’re finished.
- 5. Pry off the protective coating on the edge of each leg with a sharp knife or a prying tool such as a screwdriver tip bent into a U-shape. This will give you better access to the screws that hold them together.
- 6. Loosen and remove the screws that hold each side rail to the top surface of the table. Again,be sure to label each screw so you can put them back in the same location.
- 7. Lift up one side rail and pull it away from the top surface of the table. Repeat on the other side.
- 8. Disconnect the ball return mechanism by gently pulling on the metal rod that connects it to the striker.
- 9. Remove the striker by unscrewing its two screws, and then remove the metal rod that connects it to the cue ball rebound mechanism.
- 10. If there are any felt or padding covers on the bottom of either side rail, remove them with a knife before proceeding.
Conclusion
Pool tables can be a lot of fun to play on, but they can also be a pain to take apart and put back together. If you’re someone who loves to pool but doesn’t want to spend hours taking the table down and putting it back together, follow these simple steps to help you disassemble it quickly and easily.
